|
PULVERIZER TYPE "SV MICRO" WITH DYNAMIC AIR CLASSIFIER
These mills have an high speed vertical axis rotor on which some rigid hammers of suitable shape are fixed.
The grinding action is provided by impact against a toothed lining and by friction between layers of the processed material.
The product is pneumatically discharged upwards, through an air classifier. The dynamic classifier is designed according to the grinding requirement and is fitted onto the top of the mill.
The cage-type dynamic microclassifyer fitted onto the mill, is suitable to obtain powders at a fineness up to 99% finer than 20 micron, with an high percentage of particles finer than 5 micron. The oversize not passing through the micro-classifier falls down to the mill where it is further ground.
The drive of the micro-separator is independent and usually is made with a variable speed motor.
This allows a very fine adjustment of the working speed and the micro-separator directly from the control board.
Granulometry also depends on the mill’s speed and on the air flow.
The air flow, drawn through the mill by the exhaust blower, can be heated for drying moist products or can be cooled for treating thermo sensitive products.
The air circuit is closed under inert gas when processing products subject to explosion risks.
APPLICATION
The mills type SV are designed for the fine or finest grinding of many materials of medium hardness and abrasiveness, such as:
• Minerals (calcium carbonate, gypsum, limestone, antimonium sulphate, etc.)
• Chemical products (calcium idroxide, calcium oxide, aluminium idroxide, petroleum coke)
• Vegetable products (coals, dried vegetables, cocoa, etc).
• Micronizing of cereals.
SV MILL’S DIAGRAM
1)HOPPER
2)SCREW FEEDER
3) HAMMERS
4) GRINDING LINING
5) DYNAMIC AIR CLASSIFIER
6) OPENING SYSTEM
7) MILL’S FRAME
8) MILL’S MOTOR
9) CLASSIFIER’ S MOTOR
10) AIR VALVE
PLANT DIAGRAM
1)HOPPER
2) SCREW FEEDER
3) MILL TYPE SV IV MICRO WITH CLASSIFIER
4) FILTER
5) ROTARY VALVE
6/12) AIR FLOW CONROL
7) SUCTION BLOWER
8/10) SILENCER
9) CHIMNEY
11) AIR HEATHER, COOLER OR INERT GAS.
CONSTRUCTION FEATURE
• Screw feeder or special rotary valve feeder
• Hammers of cast high chromium alloy
• Toothed lining plates of wear resistant alloy
• Shaft of Cr.Ni steel supported by roller bearings enclosed in a dust tight box, grease lubrified.
• It is possible to supply stainless steel machines
• For any special problem please contact our technical department.
TECHNICAL CHARACTERISTICS
| SV 3 MICRO | SV 4 MICRO | SV 5 MICRO | ||
| Diameter of the mill rotor | mm | 800 | 1000 | 1300 |
| Power requirement of the mill | Kw | 22 ÷ 45 | 30 ÷ 75 | 75 ÷ 110 |
| Power requirement of micro-classifier | Kw | 4 ÷ 7,5 | 7,5 ÷ 11 | 15 |
| Power requirement of suction fan | Kw | 7,5 ÷ 22 | 11 ÷ 37 | 22 ÷ 55 |
| Hourly capacity | Kg/h | 100 ÷ 1200 | 200 ÷ 2500 | 400 ÷ 4000 |
| Mill’s speed | rpm | 1000 ÷ 2200 | 1000 ÷ 2000 | 1000 ÷ 1800 |
| Micro classifier’s speed | rpm | 500 ÷ 3000 | 500 ÷ 3000 | 400 ÷ 2500 |
| Necessary filter | mq | 20 ÷ 60 | 40 ÷ 100 | 100 ÷ 180 |
| Noise level (1 m) without noise insulation systems* | db | 90 | 90 | 93 |
*The noise level could change depending on the working conditions
Data and features may change without any previous device
DOWNLOAD TECHNICAL DATA SHEET
